IKO LM 132332 Linear Bushing
IKO LM 132332 Description
|
Shaft diameter mm | Identification number | Nominal dimensions and tolerances mm | Eccentricity
Maximum μm | Basic dynamic load rating C | Basic static load rating C0 | |||||||||||||||||||||||||||||||
| Standard type | Ball raceway | Mass (Ref.) g | Adjustable clearance type | Ball raceway | Mass (Ref.) g | Open type | Ball raceway | Mass (Ref.) g | ||||||||||||||||||||||||||||
| Dim. F w | C2 | D1 | h | E | α Degree | |||||||||||||||||||||||||||||||
| Fw | tolerance μm | D | Dim. D tolerance μm | C | Dim. C tolerance μm | C（1 1） | Dim. C1 tolerance μm | Load direction A N | Load direction B N | Load direction A N | Load direction B N | |||||||||||||||||||||||||
| P | H | P | H | |||||||||||||||||||||||||||||||||
| 6 | LM LM | 61219 61219 N | 4 4 | 8 7.6 | LM | ―――― 61219 N | AJ* | － 4 | － 7.5 | ―――― | － | － | 6 |
0 －6 |
0 — 9 | 12 |
0 －11 | 19 |
0 －200 | 13.5 |
0 －200 | 1.1 | 11.5 | － 1 | － | － |
8 |
12 | 80.7 | 92.7 | 167 | 237 | ||||
|
8 | LM LM | 81517 81517 N | 4 4 | 13 10.4 | LM | ―――― 81517 N | AJ* | － 4 | － 10 | ―――― | － | － | 8 | 15 | 17 | 11.5 | 1.1 | 14.3 | － 1 | － | － | 87.4 | 100 | 160 | 226 | |||||||||||
| LM LM | 81524 81524 N | 4 4 | 18 15 | LM | ―――― 81524 N | AJ* | － 4 | － 14.7 | ―――― | － | － | 8 | 15 | 24 | 17.5 | 1.1 | 14.3 | － 1 | － | － | 121 | 139 | 255 | 361 | ||||||||||||
| 10 | LM LM | 101929 101929 N | 4 4 | 30 27.5 | LM | ―――― 101929 N | AJ* | － 4 | － 26.5 | LM | ―――― 101929 N | OP* | － 3 | － 18 | 10 | 19 |
0 －13 | 29 | 22 | 1.3 | 18 | － 1 | － 6.8 | － 80 | 179 | 206 | 354 | 501 | ||||||||
| 12 | LM LM | 122130 122130 N | 4 4 | 29 31.5 | LM LM | 122130 122130 N | AJ* AJ* | 4 4 | 28 30.5 | LM LM | 122130 122130 N | OP* OP* | 3 3 | 19 22 | 12 | 21 | 30 | 23 | 1.3 | 20 | 1.5 | 8 | 80 | 259 | 298 | 503 | 711 | |||||||||
| 13 | LM LM | 132332 132332 N | 4 4 | 43 42.5 | LM LM | 132332 132332 N | AJ* AJ* | 4 4 | 42 41.5 | LM LM | 132332 132332 N | OP* OP* | 3 3 | 31 31 | 13 | 23 | 32 | 23 | 1.3 | 22 | 1.5 | 9 | 80 | 266 | 306 | 506 | 716 | |||||||||
| 16 | LM LM | 162837 162837 N | 4 4 | 70 69 | LM LM | 162837 162837 N | AJ* AJ* | 4 4 | 69.5 68 | LM LM | 162837 162837 N | OP* OP* | 3 3 | 58 52 | 16 | 28 | 37 | 26.5 | 1.6 | 27 | 1.5 | 11 | 80 | 426 | 489 | 766 | 1 080 | |||||||||
| 20 | LM LM | 203242 203242 N | 5 5 | 92 87 | LM LM | 203242 203242 N | AJ* AJ* | 5 5 | 91 85 | LM LM | 203242 203242 N | OP* OP* | 4 4 | 79 69 | 20 |
0 －7 |
0 －10 | 32 |
0 －16 | 42 | 30.5 | 1.6 | 30.5 | 1.5 | 11 | 60 |
10 |
15 | 562 | 668 | 1 010 | 1 470 | ||||
| 25 | LM LM | 254059 254059 N | 6 6 | 226 220 | LM LM | 254059 254059 N | AJ* AJ* | 6 6 | 222 216 | LM LM | 254059 254059 N | OP* OP* | 5 5 | 203 188 | 25 | 40 | 59 |
0 －300 | 41 |
0 －300 | 1.85 | 38 | 2 | 12 | 50 | 920 | 974 | 1 780 | 2 280 | |||||||
| 30 | LM LM | 304564 304564 N | 6 6 | 253 250 | LM LM | 304564 304564 N | AJ* AJ* | 6 6 | 250 245 | LM LM | 304564 304564 N | OP* OP* | 5 5 | 228 210 | 30 | 45 | 64 | 44.5 | 1.85 | 43 | 2.5 | 15 | 50 | 1 460 | 1 540 | 2 780 | 3 560 | |||||||||
| 35 | LM LM | 355270 355270 N | 6 6 | 388 380 | LM LM | 355270 355270 N | AJ* AJ* | 6 6 | 380 375 | LM LM | 355270 355270 N | OP* OP* | 5 5 | 355 335 | 35 |
0 －8 |
0 －12 | 52 |
0 －19 | 70 | 49.5 | 2.1 | 49 | 2.5 | 17 | 50 |
12 |
20 | 1 610 | 1 710 | 3 080 | 3 940 | ||||
| 40 | LM LM | 406080 406080 N | 6 6 | 596 585 | LM LM | 406080 406080 N | AJ* AJ* | 6 6 | 585 579 | LM LM | 406080 406080 N | OP* OP* | 5 5 | 546 500 | 40 | 60 | 80 | 60.5 | 2.1 | 57 | 3 | 20 | 50 | 2 030 | 2 150 | 3 620 | 4 640 | |||||||||
| 50 | LM LM | 5080100 5080100 N | 6 6 | 1 615 1 580 | LM LM | 5080100 5080100 N | AJ* AJ* | 6 6 | 1 595 1 560 | LM LM | 5080100 5080100 N | OP* OP* | 5 5 | 1 420 1 340 | 50 | 80 | 100 | 74 | 2.6 | 76.5 | 3 | 25 | 50 | 3 940 | 4 180 | 7 130 | 9 120 | |||||||||
IKO LM 132332 Nots
Note （1） The width of hub for fixing with circlip should be the value obtained by subtracting a circlip width value times two from the C1
dimension.
Remarks 1. “P” and “H” in Dim. Fw tolerance and Eccentricity represent precision and high, respectively.
2. Standard type and adjustable clearance type end plates are fixed with stop ring for holes.
3. The identification numbers with * are our semi-standard items.
