IKO LM 81517 N Linear Bushing
IKO LM 81517 N Description
|
Shaft diameter mm |
Identification number | Nominal dimensions and tolerances mm | Eccentricity
Maximum μm |
Basic dynamic load rating
C |
Basic static load rating
C0 |
|||||||||||||||||||||||||||||||
|
Standard type |
Ball raceway | Mass (Ref.)
g |
Adjustable clearance type |
Ball raceway | Mass (Ref.)
g |
Open type |
Ball raceway | Mass (Ref.)
g |
||||||||||||||||||||||||||||
| Dim. F w |
C2 |
D1 |
h |
E |
α Degree |
|||||||||||||||||||||||||||||||
| Fw | tolerance
μm |
D | Dim. D
tolerance μm |
C | Dim. C
tolerance μm |
C（1 1） | Dim. C1
tolerance μm |
Load direction A
N |
Load direction B
N |
Load direction A
N |
Load direction B
N |
|||||||||||||||||||||||||
| P | H | P | H | |||||||||||||||||||||||||||||||||
|
6 |
LM
LM |
61219
61219 N |
4
4 |
8
7.6 |
LM |
――――
61219 N |
AJ* |
－
4 |
－
7.5 |
―――― |
－ |
－ |
6 |
0 －6 |
0 — 9 |
12 |
0 －11 |
19 |
0 －200 |
13.5 |
0 －200 |
1.1 |
11.5 |
－
1 |
－ |
－ |
8 |
12 |
80.7 |
92.7 |
167 |
237 |
||||
|
8 |
LM
LM |
81517
81517 N |
4
4 |
13
10.4 |
LM |
――――
81517 N |
AJ* |
－
4 |
－
10 |
―――― |
－ |
－ |
8 |
15 |
17 |
11.5 |
1.1 |
14.3 |
－
1 |
－ |
－ |
87.4 |
100 |
160 |
226 |
|||||||||||
| LM
LM |
81524
81524 N |
4
4 |
18
15 |
LM |
――――
81524 N |
AJ* |
－
4 |
－
14.7 |
―――― |
－ |
－ |
8 |
15 |
24 |
17.5 |
1.1 |
14.3 |
－
1 |
－ |
－ |
121 |
139 |
255 |
361 |
||||||||||||
|
10 |
LM
LM |
101929
101929 N |
4
4 |
30
27.5 |
LM |
――――
101929 N |
AJ* |
－
4 |
－
26.5 |
LM |
――――
101929 N |
OP* |
－
3 |
－
18 |
10 |
19 |
0 －13 |
29 |
22 |
1.3 |
18 |
－
1 |
－
6.8 |
－
80 |
179 |
206 |
354 |
501 |
||||||||
|
12 |
LM
LM |
122130
122130 N |
4
4 |
29
31.5 |
LM
LM |
122130
122130 N |
AJ*
AJ* |
4
4 |
28
30.5 |
LM
LM |
122130
122130 N |
OP*
OP* |
3
3 |
19
22 |
12 |
21 |
30 |
23 |
1.3 |
20 |
1.5 |
8 |
80 |
259 |
298 |
503 |
711 |
|||||||||
|
13 |
LM
LM |
132332
132332 N |
4
4 |
43
42.5 |
LM
LM |
132332
132332 N |
AJ*
AJ* |
4
4 |
42
41.5 |
LM
LM |
132332
132332 N |
OP*
OP* |
3
3 |
31
31 |
13 |
23 |
32 |
23 |
1.3 |
22 |
1.5 |
9 |
80 |
266 |
306 |
506 |
716 |
|||||||||
|
16 |
LM
LM |
162837
162837 N |
4
4 |
70
69 |
LM
LM |
162837
162837 N |
AJ*
AJ* |
4
4 |
69.5
68 |
LM
LM |
162837
162837 N |
OP*
OP* |
3
3 |
58
52 |
16 |
28 |
37 |
26.5 |
1.6 |
27 |
1.5 |
11 |
80 |
426 |
489 |
766 |
1 080 |
|||||||||
|
20 |
LM
LM |
203242
203242 N |
5
5 |
92
87 |
LM
LM |
203242
203242 N |
AJ*
AJ* |
5
5 |
91
85 |
LM
LM |
203242
203242 N |
OP*
OP* |
4
4 |
79
69 |
20 |
0 －7 |
0 －10 |
32 |
0 －16 |
42 |
30.5 |
1.6 |
30.5 |
1.5 |
11 |
60 |
10 |
15 |
562 |
668 |
1 010 |
1 470 |
||||
|
25 |
LM
LM |
254059
254059 N |
6
6 |
226
220 |
LM
LM |
254059
254059 N |
AJ*
AJ* |
6
6 |
222
216 |
LM
LM |
254059
254059 N |
OP*
OP* |
5
5 |
203
188 |
25 |
40 |
59 |
0 －300 |
41 |
0 －300 |
1.85 |
38 |
2 |
12 |
50 |
920 |
974 |
1 780 |
2 280 |
|||||||
|
30 |
LM
LM |
304564
304564 N |
6
6 |
253
250 |
LM
LM |
304564
304564 N |
AJ*
AJ* |
6
6 |
250
245 |
LM
LM |
304564
304564 N |
OP*
OP* |
5
5 |
228
210 |
30 |
45 |
64 |
44.5 |
1.85 |
43 |
2.5 |
15 |
50 |
1 460 |
1 540 |
2 780 |
3 560 |
|||||||||
|
35 |
LM
LM |
355270
355270 N |
6
6 |
388
380 |
LM
LM |
355270
355270 N |
AJ*
AJ* |
6
6 |
380
375 |
LM
LM |
355270
355270 N |
OP*
OP* |
5
5 |
355
335 |
35 |
0 －8 |
0 －12 |
52 |
0 －19 |
70 |
49.5 |
2.1 |
49 |
2.5 |
17 |
50 |
12 |
20 |
1 610 |
1 710 |
3 080 |
3 940 |
||||
|
40 |
LM
LM |
406080
406080 N |
6
6 |
596
585 |
LM
LM |
406080
406080 N |
AJ*
AJ* |
6
6 |
585
579 |
LM
LM |
406080
406080 N |
OP*
OP* |
5
5 |
546
500 |
40 |
60 |
80 |
60.5 |
2.1 |
57 |
3 |
20 |
50 |
2 030 |
2 150 |
3 620 |
4 640 |
|||||||||
|
50 |
LM
LM |
5080100
5080100 N |
6
6 |
1 615
1 580 |
LM
LM |
5080100
5080100 N |
AJ*
AJ* |
6
6 |
1 595
1 560 |
LM
LM |
5080100
5080100 N |
OP*
OP* |
5
5 |
1 420
1 340 |
50 |
80 |
100 |
74 |
2.6 |
76.5 |
3 |
25 |
50 |
3 940 |
4 180 |
7 130 |
9 120 |
|||||||||
IKO LM 81517 N Nots
Note （1） The width of hub for fixing with circlip should be the value obtained by subtracting a circlip width value times two from the C1
dimension.
Remarks 1. “P” and “H” in Dim. Fw tolerance and Eccentricity represent precision and high, respectively.
2. Standard type and adjustable clearance type end plates are fixed with stop ring for holes.
3. The identification numbers with * are our semi-standard items.
