IKO LMG 13 Linear Bushing G
IKO LMG 13 Description
| Identification number | Interchangeable | Mass (Ref.) g | Nominal dimensions and tolerances mm | Basic dynamic load rating
C N | Basic static load rating
C0 N | Dynamic（5） torque rating
T N・m | Static（5） torque rating
T0 N・m | |||||||||||||
| External cylinder | Shaft with grooved raceway（1） | M×depth（2） | d（2 3） | K | L（4） | Maximum length | ||||||||||||||
| D | Dim. D tolerance | C | Dim. C tolerance | d | Dim. d tolerance | |||||||||||||||
| LMG 6 | ○ | 9.4 | 22.0 | 12 | 0 | 19 | 0 | M2.5×1.9 | 6 | 0 | 5.2 | － | 150 200 | 300 | 587 | 641 | 2.1 | 2.2 | ||
| －0.011 | －0.200 | （2.5） | －0.012 | |||||||||||||||||
| LMGT 6 | ○ | 19.5 | 2 | |||||||||||||||||
| LMG 8 | ○ | 15.7 | 39.3 | 15 | 0 | 24 | 0 | M3 ×2.4 | 8 | 0 | 7 | － | 150 200 250 | 500 | 769 | 962 | 3.5 | 4.3 | ||
| －0.011 | －0.200 | （3） | －0.015 | |||||||||||||||||
| LMGT 8 | ○ | 33.7 | 3 | 400 | ||||||||||||||||
| LMG 10 | ○ | 31.5 | 61.2 | 19 | 0 | 29 | 0 | M3 ×3.1 | 10 | 0 | 8.9 | － | 200 300 | 600 | 1 410 | 1 710 | 8.0 | 9.7 | ||
| －0.013 | －0.200 | （4） | －0.015 | |||||||||||||||||
| LMGT 10 | ○ | 51.4 | 4 | |||||||||||||||||
| LMG 13 | ○ | 45.4 | 104 | 23 | 0 | 32 | 0 | M3 ×3.4 | 13 | 0 | 11.9 | － | 200 300 400 | 800 | 1 880 | 2 150 | 13.7 | 15.7 | ||
| －0.013 | －0.200 | （4.5） | －0.018 | |||||||||||||||||
| LMGT 13 | ○ | 81.4 | 6 | |||||||||||||||||
| LMG 16 | ○ | 78.2 | 157 | 28 | 0 | 37 | 0 | M4 ×4.1 | 16 | 0 | 14 | － | 200 300 400 | 1 000 | 2 590 | 2 930 | 23.1 | 26.1 | ||
| －0.013 | －0.200 | （5.5） | －0.018 | |||||||||||||||||
| LMGT 16 | ○ | 118 | 8 | |||||||||||||||||
| LMG 20 | ○ | 110 | 246 | 32 | 0 | 42 | 0 | M4 ×4.1 | 20 | 0 | 17.5 | － | 300 400 500 600 | 1 000 | 3 010 | 3 660 | 32.8 | 39.9 | ||
| －0.016 | －0.200 | （5.5） | －0.021 | |||||||||||||||||
| LMGT 20 | ○ | 185 | 10 | |||||||||||||||||
IKOLMG 13 Nots
Notes （1） The mass of the shaft with grooved raceway is the value per 100 mm of the track groove part.
（2） The values in （ ） are the maximum fixing thread depth.
（3） d2 represents the maximum diameter for end machining. (Perform annealing if end machining will be performed.)
（4） Represents standard length. We can produce other than the standard length, please specify the length of the shaft with grooved
raceway by indicating the length in mm with the identification number.
（5） Applicable under loaded conditions with an unidirectional torque at all times.
Use IKO Linear Ball Spline G under loaded conditions with a rotating torque bi-directionally or repeatedly.
Remark: Linear Bushing G are all interchangeable specification.
