IKO LWLF 2(2) C-LUBE LINEAR WAY ML
IKO LWLF 2(2) Description
| Identification number | Interchangeable | Mass (Ref.) g | Dimensions of assembly mm | Dimensions of slide unit mm | Dimensions of track rail mm | Appended mounting bolt for track rail mm
Bolt size× | Basic dynamic load rating（4）
C N | Basic static load rating（4）
C0 N | Static moment rating（4） | ||||||||||||||||||||||
| MLF series | LWLF series （No C-Lube） | Slide unit | Track rail （per 100 mm） | H | H1 | N | W2 | W3 | W4 | L1 | L2 | L3 | M1×depth | H2 | H3 | W | H4 | M2 | d3 | d4 | h | E | F | T0 N･m | TX N･m | TY N･m | |||||
| － | LWLF 2（2） | － | 0.21 | 2 | 2.5 | 0.5 | 1.5 | 5 | － | － | 6.5 | 2 | 3.9 | M1 × 0.9 | 1.2 | － | 2 | 1.4 | M1 Through | － | － | － | 3 | 6 | M1× （3） （Not appended） | 66.8 | 118 | 0.12 | 0.07 0.47 | 0.09 0.56 | |
| － | LWLF 4（2） | － | 2.1 | 6.8 | 4 | 1 | 3 | 10 | － | 5 | 17 | 6.5 | 11.9 | M2 × 1.3 | － | － | 4 | 2.6 | － | 1.8 | 2.8 | 0.75 | 5 | 10 | Cross-recessed pan head screw for precision equipment M1.6×5 | 390 | 677 | 1.4 | 1.3 7.1 | 1.5 8.4 | |
| MLFC 6（2） | － | 2.1 | 13 |
4.5 |
1 |
3 |
12 |
－ |
6 |
15 |
4.5 |
9.8 |
M2 × 1.6 |
－ |
－ |
6 |
2.8 | － | 2.4 | 4 | 1.5 |
7.5 |
15 | Cross-recessed pan head screw for precision equipment M2×4 |
334 |
542 |
1.7 |
0.84 5.1 |
1.0 6.1 | ||
| LWLFC 6（2） | － | 2.4 | |||||||||||||||||||||||||||||
| MLFC 6…N（2）＊ | － | 2.1 | 12 | M3 Through | － | － | － | M3× （3） （Not appended） | |||||||||||||||||||||||
| LWLFC 6…N（2）＊ | － | 2.4 | |||||||||||||||||||||||||||||
| MLF 6（2） | － | 3.1 | 13 |
20 |
8 |
14.6 | － | 2.4 | 4 | 1.5 | Cross-recessed pan head screw for precision equipment M2×4 |
443 |
813 |
2.5 |
1.8 9.9 |
2.2 11.8 | |||||||||||||||
| LWLF 6（2） | － | 3.4 | |||||||||||||||||||||||||||||
| MLF 6…N（2）＊ | － | 3.1 | 12 | M3 Through | － | － | － | M3× （3） （Not appended） | |||||||||||||||||||||||
| LWLF 6…N（2）＊ | － | 3.4 | |||||||||||||||||||||||||||||
IKO LWLF 2(2) Nots
Notes （1）Track rail lengths L are shown in Table 3.2 on page Ⅱ－11.
（2） Steel balls are not retained. No end seal is attached.
（3）Choose screws whose dimension allow fixing thread depth into track rail R to be less than H4.
（4） The direction of basic dynamic load rating (C), basic static load rating (C0), and static moment rating (T0, TX, TY) are shown in the
sketches below.
The upper values of TX and TY are for one slide unit and the lower values are for two slide units in close contact.
Remarks 1. The identification numbers with * are our semi-standard items.
2. There is no oil hole on the slide unit.
IKO LWLF 2(2) Example of identification number of assembled set
